Active Military and Aerospace Standards Requiring or Governing Silver

Back

MIL-DTL-1183

  • This specification covers pipe fittings of cast bronze with at least one end for silver-brazing into steam, air, oil, or water piping systems.

MIL-B-1563

  • This specification covers the requirements for buttons, insignia and findings used by the United States Military Academy.

MIL-PRF-2939

  • This specification covers duct type and gravity type air cooling coils for use in Naval shipboard environmental control systems.

MIL-DTL-3461

  • This specification covers metal uniform and cap buttons with embossed designs used by the Military Departments.

MIL-DTL-3628

  • This specification covers the general requirements of Aviation, identification, occupational, and qualification badges, badge clasps, bars, and pendants used by the Department of Defense and other Government Agencies.

MIL-DTL-3928

  • This specification covers the general requirements for coaxial and pin-mounted switches, either manually or remotely controlled, for use with coaxial cable or with microstrip at radio and microwave frequencies.

MIL-DTL-3943

  • This specification covers the requirements for decorations and medals awarded by the Department of Defense and other Government Agencies.

MIL-DTL-5002

  • This specification covers the requirements for cleaning, surface treatment, and application of inorganic coatings for metallic surfaces of weapons systems parts.

MIL-PRF-8805

  • Switch, Assemblies, Sensitive, Trigger, 7 Amperes, Unsealed

 MIL-DTL-11484

  • This specification covers the general requirements of lapel buttons used by the Department of Defense and various Federal agencies.

MIL-DTL-11589

  • Ribbons & Medals - U.S. Coast Guard, NASA, Commerce, ARMY JROTC, SILVER STAR

MIL-DTL-13282C

  • This specification covers fine silver and two silver-copper alloys.

MIL-DTL-14639F SUP 1

  • This specification covers the general requirements of lapel buttons used by the Department of Defense and various Federal agencies.

MIL-DTL-17361

  • Sets forth, for use by qualified personnel, a number of basic procedures that may be used for the inspection and preventive maintenance of molded case circuit breakers used in industrial and commercial applications rated up to and including 1000 V 50/60 Hz AC or AC/DC.

MIL-V-17501

  • This specification covers magazine and hangar deck sprinkler control type valves for shipboard service.

MIL-B-18855

  • This specification establishes the requirements for the procurement of Battery MK 53 MOD 0 Secondary Type, Silver-Zinc-Alkali, Naval Ordnance Systems Command LD 476652. The battery is of one type and one class.

MIL-PRF-20042G

  • This specification covers 50-, 100-, 150-, 250-, and 400-pound silver brazing bronze pipe flanges for use with water, oil, gas, or steam service not to exceed 425 °F.

MIL-PRF-22710/12J

  • Switches, Code Indicating Wheel (Printed Circuit), (Thumbwheel Switch Assembly, Sealed Modules, Illuminated or Non-Illuminated), (Top Relampable), Style SRPC12.

MIL-PRF-22710/15K

  • Switches, Code Indicating Wheel (Printed Circuit), (Thumbwheel Switch Assembly, Sealed Modules, Illuminated or Non-Illuminated), (Top, Bottom, or Rear Relampable), Style SRPC15

MIL-PRF-22885/101F

  • Switch, Pushbutton, Illuminated, 4-Lamp, SPDT and DPDT, 5.0 Amperes Silver Contacts, 1 Ampere Max. Gold Contacts, Dripproof, Sunlight Readable, EMI/RFI Shielded, NVIS Compatible

MIL-PRF-22885/108K

  • Switch, Pushbutton, Illuminated, 4-Lamp, SPDT and DPDT, 5.0 Amperes Silver Contacts, 1 Ampere Max. Gold Contacts, Dripproof, Sunlight Readable, EMI/RFI Shielded, NVIS Compatible

MIL-C-23233A NOT 1

  • This specification covers flexible couplings for propulsion units, auxiliary equipment, and line shafts.
  • Couplings for Propulsion Units, Auxiliary Turbines and Line Shafts, Naval Shipboard

MIL-DTL-23919D NOT 1

  • The specification covers the design, fabrication, and testing of silver-silver chloride (Ag/AgC1) reference cells.  The reference cell, also known as a reference electrode, is a half cell with very consistent reproducible potential (voltage) against which the potentials of other metals are measured.  The potential measurement is provided as a voltage signal to an impressed current cathodic protection (ICCP) system controller and may be used to control and monitor the ICCP system operation.

MIL-DTL-23971E(1)

  • Power Dividers, Power Combiners, and Power Divider/Combiners, General Specification for
  • his specification covers the general requirements for power dividers, power combiners, and power divider/combiners. Specific requirements tailored for “space flight application” components are included to represent the highest reliability components specified herein. Such components are intended for use in NASA manned, satellite, interplanetary or launch vehicle programs.

MIL-DTL-24135/12A(1) NOT 1

  • This specification covers high performance synthetic rubber hose, sizes -4 through -40, wire reinforced with a single-wire braid over a single layer of synthetic fiber braid that are used in flexible hose assemblies for medium pressure, high temperature, multi-fluid applications. This hose is compatible with petroleum, petroleum-based synthetic, and phosphate ester-based oils.

MIL-DTL-24136/1B NOT 1

  • This specification covers flexible, synthetic fiber reinforced rubber hose and hose assemblies, sizes -80 through -192, for use in low pressure applications.

MIL-DTL-24227A NOT 1

  • This specification covers tube fittings and flanges of cast bronze with ends for silver-brazing into a piping system suitable for ultrasonic inspection. Fittings are interior streamlined from socket-to-socket for use with inserted rings of silver-brazing alloy. Flanges are suitable for use with inserted rings of silver-brazing alloy. These fittings and flanges are not suitable for use in drinking (potable) water systems.

MIL-DTL-28748E

  • This specification covers rectangular, rack and panel, electrical connectors, with nonremovable solder type contacts, and removable crimp type contacts, intended for use in electronic and electrical equipment.

MIL-DTL-28837D NOT 1

  • This specification covers the general requirements for mixer stages, radio frequency for use in military systems.

MIL-DTL-28875C(1) SUP 1 NOT 1

  • This specification establishes the general requirements for solid-state RF and microwave amplifiers and the verification requirements which must be met in the acquisition of amplifiers. Detail requirements, specific characteristics of amplifiers and other provisions are specified in the applicable specification sheet.

MIL-DTL-32101B(2) NOT 1

  • This specification covers activated carbon impregnated with copper, silver, zinc and molybdenum compounds and triethylenediamine (TEDA) for use as a sorbent for all known and suspected military chemical weapons agents. Throughout this specification, the term “carbon” refers to an impregnated, activated carbon. For definitions of sampling terms used in this specification.

MIL-DTL-32139B(2)

  • This specification covers the detail requirements for nanominiature connectors terminated on printed circuit boards or attached to cable assemblies. The connector contacts are densely packed with .025 (0.64 mm) inch spacing between contact centers in the same row. These connectors are intended for use in assemblies requiring very densely packaged electronic components and are commonly used in digital applications.

MIL-DTL-32689(3)

  • This specification covers the general requirements for environment resisting, electromagnetic/radiofrequency interference (EMI/RFI) shielded connectors. Connectors achieve full mating with one 360° turn using a triple-start threaded coupling system. Plug connectors include a ratcheting, anti-decoupling mechanism. Plugs and receptacles have keyed shells and removable, rear release crimp contacts. Shell style options include shells with integrated banding platforms and shells with rear accessory threads. Contact mating end sizes include sizes 23, 20, 20HD, 16 and 12. Connectors support applications with contacts at sea level, DWV tested up to 1800 Vac (rms) and are capable of operating within a temperature range of -65°C to +200°C, depending on class (see table II). Connectors are tested to withstand 37 g’s random vibration and 300 g’s shock. See 6.1 for intended use and applications. Ollie dimensions are in inches.

MIL-DTL-38999N(1)

  • This specification covers four series of miniature, high density, circular, environment resistant electrical connectors with removable crimp contacts, or hermetically sealed electrical connectors with fixed, nonremovable contacts. Both environment resistant and hermetically sealed connectors are available with bayonet, threaded, or breech-coupled mating systems. Connectors are capable of operating within a temperature range of -65°C to +200°C maximum, or as specified herein (see 1.4). See 6.1 for intended use, application notes, application restrictions and derating factors.

MIL-PRF-39012F(4) SUP 1

  • This specification covers the general requirements and tests for radio frequency connectors used with flexible RF cables and certain other types of coaxial transmission lines.

MIL-DTL-41819D

  • This specification covers ribbon attachments for decorations, medals and service ribbons.

MIL-PRF-55339C(4) SUP 1 NOT 1

  • This specification covers the performance requirements and tests for between series and within series, radio frequency (RF), coaxial connector adapters.

MIL-DTL-81381C(1) SUP 1 NOT 2

  • This specification covers polyimide-insulated single conductor electric wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified in the applicable specification sheet. The polyimide insulation may be used alone or in combination with other insulation materials.

MIL-DTL-83528/14B NOT 1

  • Gasketing Material, Conductive, Shielding Gasket, Electronic, Elastomer, EMI/RFI, for use in Time Totalizing Meters Covered by MIL-M-7793.

MIL-DTL-83733E(4) SUP 1

  • This specification covers environment and fluid resisting, miniature, rectangular type, rack to panel electrical connectors (plugs and receptacles). These connectors utilize rear release, removable crimp type contacts and are capable of continuous operation from -65 Degrees C to +200 Degrees C.

MIL-DTL-83734J

  • This specification covers plug-in electronic component sockets for use on panel boards, printed circuit boards, and microelectronic component.

MIL-DTL-85110B NOT 1

  • This specification establishes the requirements for the design, construction, performance, and test of the repeatable release holdback bar (RRHB) for use on carrier-type aircraft.

MS9197D(3) NOT 2

  • Nut, Tube Coupling-CRES SAE-AMS5646, Silver Plate

MS9315D

  • Cap Assembly, Tube - SAE-AMS5646, Silver Plated Nut

A-A-59287A NOT 4

  • This commercial item description (CID) covers a single turret feedthru stud terminal.

A-A-59288A NOT 4

  • This commercial item description (CID) covers a single-double turret feedthru stud terminal.

A-A-59289B NOT 3

  • This commercial item description (CID) covers a double-double turret, feedthru stud terminal.

A-A-59339 NOT 1

  • This CID covers the general requirements for Guanidine Nitrate (GN) used in military explosives.

A-A-59569D

  • This commercial item description (CID) covers the general requirements for braid, wire (copper, tin-coated, silver-coated, or nickel coated, tubular or flat). Braid, wire (copper, tin-coated, silver-coated, or nickel coated, tubular or flat) covered by this CID are intended for commercial/industrial applications.

A-A-59974 NOT 1

  • This commercial item description (CID) covers metal polish cleaners suitable for polishing and as a tarnish preventive for aluminum, brass and related alloys, bronze, chrome, copper, nickel, stainless steel, sterling silver, or silver-plated articles.

A-A-59976 NOT 1

  • This commercial item description (CID) covers a pre-soak cleaner without chemical sanitizing properties that has the capability (without enzymes or microbial agents) to break down soils on stainless steel and silver flatware.

O-F-499D NOT 2

  • This specification covers low-melting-point fluxes for use with silver brazing filler metal in brazing ferrous and nonferrous metals, excluding light metals and their alloys.

QQ-B-654A(1) NOT 2

  • BRAZING ALLOYS, SILVER

QPL-23919 NOT 1

  • Reference Cell, Silver-Silver Chloride-Impressed Current Cathodic Protection (ICCP).

MIL-HDBK-406(2) NOT 3

  • This Handbook serves as a guide and establishes the minimum requirements for selection, storage and compatibility considerations of cleaning agents for use in Clean Rooms and Clean Work Stations and Controlled Environmental Facilities.

MIL-HDBK-407(1) NOT 3

  • The purpose of this program is to delineate requirements to that extent necessary to establish general data for operational and performance characteristics essential to developing an adequate document support structure suitable for use in contamination control technology.

MIL-HDBK-730

  • The purpose of this handbook is to provide Department of Defense engineering and quality assurance personnel with the basic principles and general knowledge of materials joining processes.

ADA1

  • This specification is for alloy, composed essentially of silver and tin, used in the preparation of dental amalgam.

ASTM-B32

  • This specification covers solder metal alloys (commonly known as soft solders), including tin-lead, tin-antimony, tin-antimony-copper-silver, tin-antimony-copper-silver-nickel, tin-silver, tin-copper-silver, and lead-tin-silver, used for the purpose of joining together two or more metals at temperatures below their melting points.

ASTM-B122/B122M

  • This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar.

ASTM-B206/B206M

  • This specification establishes the requirements for wire in round, hexagonal, octagonal, rectangular and square form of UNS Alloy Nos. C71000, C74500, C75200, C75700, C76400, C77000 and C79200.

ASTM-B298

  • This specification covers silver-coated, soft or annealed, round copper wire, intended for use in electrical equipment.

ASTM-B477

  • This specification covers 75 percent gold-22 percent silver-3 percent nickel alloy tuing, rod, wire, strip, and sheet material for sliding electrical contacts.

ASTM-B501

  • This specification covers silver-coated, round, copper-clad steel wire for electronic application.

ASTM-B522

  • This specification covers 69% gold, 25% silver, 6% platinum alloy tubing, rod, wire, and sheet material for sliding electrical contacts.

ASTM-B563

  • This specification covers an alloy containing palladium, silver, copper, platinum, and nickel in the form of wire, rod, and strip for electrical contacts.

ASTM-B617

  • This specification covers 90 percent silver - 10 percent copper alloy tubing, rod, wire, strip, and sheet material for electrical contacts.

ASTM-B628

  • This specification cover 72 percent silver - 28 percent copper (eutectic) alloy rod, wire, strip, and sheet material for electrical contacts.

ASTM-B663

  • This specification covers electrical contact components made from silver-tungsten carbide by powder metallurgical procedures.

ASTM-B780

  • This specification covers an electrical contact material with the nominal composition of 75 percent silver, 24.5 percent copper, and 0.5 percent nickel in the form of rod, wire, strip, and sheet.

ASTM-D2988

  • These test methods cover the determination of water-extractable halide ion in halogenated organic solvents and their admixtures. Fluoride ion is not measured due to the solubility of silver fluoride. THis test method covers the determination of chloride ion in halogenated organic solvents and their admixtures.

IPC-TM650.2.3.33

  • This test method is designed to determine the presence (if any) of chlorides and bromides in soldering flux by visual examination after placement on test paper.

SAE-AMS2410

  • This specification covers the requirements for electrodeposited silver on other metals, usually with a nickel strike between the basis metal and the silver.

SAE-AMS2411

  • This specification covers the engineering requirements for electrodeposition of silver on other metals, usually with a nickel strike between the basis metal and the silver, and the properties of the deposit.

SAE-AMS2412

  • This specification covers the engineering requirements for electrodeposition of silver, usually with a copper strike between the basis metal and the silver, and the properties of the deposit.

SAE-AMS2413

  • This specification covers the engineering requirements for electrodeposition of silver and rhodium and the properties of the deposit.

SAE-AMS3410

  • This specification covers a silver-brazing flux in the form of a paste which contains not more than 35% water by weight.

SAE-AMS4765

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips, and a viscous mixture (paste) of powder in a suitable binder.

SAE-AMS4766

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

SAE-AMS4767

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

SAE-AMS4770

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips, and a viscous mixture (paste) of powder in a suitable binder.

SAE-AMS4771

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

SAE-AMS4772

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

SAE-AMS4773

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

SAE-AMS4774

  • This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

SAE-AS3477

  • NUT, SELF LOCKING - DOUBLE HEXAGON, EXTENDED WASHER, UNS S66286, SILVER PLATED, UNJ THREAD

SAE-AS3485

  • NUT, SELF-LOCKING, 12 POINT, REDUCED HEIGHT, SILVER PLATE, UNS S66285

SAE-AS3505

  • Insert – Thin Wall, Long, Self-Locking, 1025° F, Silver Plated On Internal Surfaces Only, UNS N07718, UNJ Thread

SAE-AS9201

  • Nut, Plain, Hexagon, Boss Connection, Silver Plated, 347 CRES UNS S34700

SAE-AS9357

  • NUT, PLAIN, HEXAGON, SILVER PLATED, UNS S66286 130 KSI MIN

SAE-AS9359

  • Nut, Castellated, Hexagon, Silver Plated, Cres UNS S66286, 130 ksi min

SAE-AS9360

  • Nut, Plain, Hexagon - Drilled, Silver Plated - UNS S66286, 130 KSI MIN

SAE-AS9362

  • Nut, Plain, Hexagon, Check - UNS S66286, 130 KSI MIN, Silver Plated

SAE-AS9364

  • Nut, Slotted, Hexagon, Shear - Silver Plated, UNS S66286, 130 KSI MIN

SAE-AS9371

  • GASKET-METAL O-RING, .035 TUBE X .006 WALL, SILVER PLATED

SAE-AS9372

  • GASKET-METAL O-RING, .062 TUBE X .006 WALL, SILVER PLATED

SAE-AS9373

  • GASKET - METAL O-RING, .062 TUBE X .010 WALL SILVER PLATED

SAE-AS9374

  • GASKET METAL O-RING, .094 TUBE X .006 WALL, SILVER PLATED

SAE-AS9375

  • GASKET-METAL O-RING, .094 TUBE X .010 WALL, SILVER PLATED

SAE-AS9376

  • GASKET-METAL O-RING, .125 TUBE X .010 WALL, SILVER PLATED

SAE-AS9572

  • Screw, Machine – Double Hexagon Extended Washer Head, Drilled, PD Shank, Silver Plated Corrosion and Heat Resistant Steel, UNS S66286, 130 KSI Min, .1380-40 UNJF-3A

SAE-AS9573

  • Screw, Machine – Double Hexagon Extended Washer Head, Drilled, PD Shank, Silver Plated Corrosion and Heat Resistant Steel, UNS S66286, 130 KSI Min, .1640-36 UNJF-3A

SAE-AS9574

  • Bolt, Machine - Double Hexagon Extended Washer Head, Drilled, PD Shank, Silver Plated, Corrosion and Heat Resistant Steel, UNS S66286, 130 KSI MIN, .190-32 UNJF-3A

SAE-AS9575

  • BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, SILVER PLATED, .250-28 UNJF-3A

SAE-AS9576

-BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, SILVER PLATED, .3125-24 UNJF-3A

SAE-AS9577

  • Bolt, Machine – Double Hexagon Extended Washer Head, Drilled, PD Shank, UNS S66286, Silver Plated, .3750-24 UNJF-3A

SAE-AS9712

  • Screw, Machine – Double Hexagon, Extended Washer Head, Drilled, Silver Plated, Nickel Alloy (UNS N07001), .1380-40 UNJF-3A

SAE-AS9714

  • BOLT, MACHINE-DOUBLE HEXAGON, EXTENDED WASHER HEAD, DRILLED, SILVER PLATED, CORROSION AND HEAT RESISTANT STEEL, .190-32 UNJF-3A

SAE-AS9715

  • Bolt, Machine-Double Hexagon, Extended Washer Head, Drilled, Silver Plated, Corrosion and Heat Resistant Nickel Alloy, .2500-28 UNJF-3A

SAE-AS9716

  • Bolt, Machine - Double Hexagon, Extended Washer Head, Drilled, Silver Plated, Corrosion and Heat Resistant Steel, .3125-24 UNJF-3A

SAE-AS22759/1

  • Wire, Electrical, Fluoropolymer-Insulated, PTFE And PTFE-Coated Glass, Silver-Coated Copper Conductor, 600-Volt

SAE-AS22759/4

  • Wire, Electric, Fluoropolymer-Insulated, TFE-Glass-FEP, Medium Weight, Silver-Coated Copper Conductor, 600-Volt

SAE-AS22759/7

  • Wire, Electric, Fluoropolymer-Insulated, Abrasion Resistant Extruded PTFE, Medium Weight, Silver-Coated Conductor, 600 Volt

SAE-AS22759/9

  • Wire, Electrical, Fluoropolymer-Insulated, Extruded Tfe, Silver-Coated Copper Conductor, 1000 Volt

SAE-AS22759/11

  • Wire, Electrical, Fluoropolymer-Insulated, Extruded TFE, Silver-Coated Copper Conductor, 600-Volt

SAE-AS22759/15

  • Wire, Electric, Fluoropolymer-Insulated, FEP-PVF2, Light Weight, Silver-Coated High Strength Copper Alloy Conductor, 600-Volt

SAE-AS22759/17

  • Wire, Electric, Fluoropolymer-Insulated, Extruded ETFE, Medium Weight, Silver-Coated High Strength Copper Alloy Conductor, 600-Volt, 150 Degrees C

SAE-AS22759/19

  • Wire, Electric, Fluoropolymer-Insulated, Extruded ETFE, Light Weight, Silver-Coated High Strength Copper Alloy Conductor, 600-Volt, 150 Degrees C

SAE-AS22759/20

  • Wire, Electric, Fluoropolymer-Insulated, Extruded TFE, Silver-Coated High Strength Copper Alloy Conductor, 1000-Volt

SAE-AS22759/22

  • Wire, Electric, Fluoropolymer-Insulated, Extruded TFE, Silver-Coated High Strength Copper Alloy Conductor, 600-Volt

SAE-AS22759/28

  • Wire, Electric, Fluoropolymer-Insulated, Extruded TFE, Polyimide Coated, Silver-Coated Copper Conductor, 600-Volt

SAE-AS22759/30

  • Wire, Electric, Fluoropolymer-Insulated, Extruded TFE, Polyimide Coated, Silver-Coated High Strength Copper Alloy Conductor, 600-Volt

SAE-AS22759/33

  • Wire, Electrical, Fluoropolymer-Insulated, Crosslinked Modified ETFE, Lightweight, Silver-Coated, High-Strength Copper Alloy, 200 Degrees C, 600-Volt

SAE-AS22759/35

  • Wire, Electrical, Fluoropolymer-Insulated, Crosslinked Modified ETFE, Normal Weight, Silver-Coated, High-Strength Copper Alloy, 200 C, 600-Volt

SAE-AS22759/43

  • Wire, Electrical, Fluoropolymer-Insulated, Crosslinked Modified ETFE, Normal Weight, Silver-Coated High-Strength Copper Alloy, 200 C, 600 Volt

SAE-AS22759/44

  • Wire, Electrical, Fluoropolymer-Insulated, Crosslinked Modified ETFE, Lightweight, Silver-Coated Copper, 200 C, 600 Volt

SAE-AS22759/81

  • Wire, Electrical, Polytetrafluoroethylene/Polyimide Insulated, Light Weight, Silver-Coated, High Strength Or Ultra High Strength Copper Alloy, 200 C, 600 Volts

SAE-AS22759/83

  • Wire, Electrical, Polytetrafluoroethylene/Polyimide Insulated, Normal Weight, Silver Coated, Copper Conductor, 200 C, 600 Volts

SAE-AS22759/86

  • Wire, Electrical, Polytetrafluoroethylene/Polyimide Insulated, Normal Weight, Silver Coated, Copper Conductor, 200 C, 600 Volts

SAE-AS22759/89

  • Wire, Electrical, Polytetrafluoroethylene/Polyimide Insulated, Normal Weight, Silver Coated, High Strength Or Ultra High Strength Copper Alloy, 200 C, 600 Volts

SAE-AS22759/91

  • Wire, Electrical, Polytetrafluoroethylene/Polyimide Insulated, Lightweight, Silver Coated, Copper Conductor, 200 C, 600 Volts

SAE-AS50861

  • This specification covers polyvinyl chloride insulated conductor electric wires made with tin-coated copper conductors or silver-coated copper alloy conductors as specified in the applicable military specification sheet.

SAE-AS50861/6

  • Wire, Electrical, Polyvinyl Chloride Insulated, Polyvinylidene Fluoride Jacket, Silver-Coated Copper Alloy Conductor, 600-Volt, 110 Degrees C

SAE-AS81044

  • This specification covers single conductor electric wires made as specified in the applicable specification sheet with tin-coated, silver-coated, or nickel-coated copper or copper alloy conductors insulated with crosslinked polyalkene, crosslinked alkane-imide polymer, or polyarylene.

SAE-AS81044/5

  • Wire, Electric, Crosslinked Polyalkene Insulated, Silver-Coated Copper, Normal Weight, 600-Volt, 150 Degrees C

SAE-AS81044/7

  • Wire, Electric, Crosslinked Polyalkene Insulated, Silver-Coated High Strength Copper Alloy, Normal Weight, 600-Volt, 150 Degrees C

SAE-AS81044/8

  • Wire, Electric, Crosslinked Polyalkene Insulated, Silver-Coated Copper, Medium Weight, 600-Volt, 150 Degrees C

SAE-AS81044/10

  • Wire, Electric, Crosslinked Polyalkene Insulated, Silver-Coated High Strength Copper Alloy, Medium Weight, 600-Volt, 150 Degrees C

SAE-AS81044/11

  • Wire, Electric, Crosslinked Polyalkene Insulated, Silver-Coated Copper, Light Weight, 600-Volt, 150 Degrees C

SAE-AS81044/13

  • Wire, Electric, Crosslinked Polyalkene Insulated, Silver-Coated High Strength Copper Alloy, Light Weight, 600-Volt, 150 Degrees C

SAE-AS81822/1

  • WIRE, ELECTRICAL, SOLDERLESS WRAP, POLYETHYLENE TEREPHTHALATE-POLYESTER LAMINATED TAPE INSULATION, SILVER COATED SOLID CONDUCTOR

SAE-AS81822/3

  • WIRE, ELECTRICAL, SOLDERLESS WRAP, EXTRUDED POLYVINYIDENE FLUORIDE (PVDF) INSULATION, SILVER COATED SOLID CONDUCTOR

SAE-AS81822/4

  • Wire, Electrical, Solderless Wrap, Polyimide Coating Over Extruded Polytetrafluoroethylene (PTFE) Insulation, Silver Coated Solid Conductor

SAE-AS81822/5

  • WIRE, ELECTRICAL, SOLDERLESS WRAP, FLUOROCARBON POLYIMIDE TAPE AND POLYTETRAFLUOROETHYLENE (PTFE) INSULATION, SILVER COATED SOLID CONDUCTOR

SAE-AS81822/6

  • Wire, Electrical, Solderless Wrap, Extruded Polytetrafluoroethylene (PTFE) Insulation, Silver Coated Solid Conductor

SAE-AS81822/8

  • Wire, Electrical, Solderless Wrap, Polyimide Jacket Over Fluorinated Ethylene Propylene (FEP) Insulation, Silver Coated Solid Conductor

SAE-AS81822/10

  • Wire, Electrical, Solderless Wrap, Uninsulated, Silver Coated Solid Conductor

SAE-AS81822/13

  • Wire, Electrical, Solderless Wrap, Extruded Ethylene- Tetrafluoroethylene (ETFE) Insulation, Silver Coated Solid Conductor

SAE-AS81822/15

  • Wire, Electrical, Solderless Wrap, Extruded Ethylene- Chlorotrifluoroethylene (ECTFE) Insulation, Silver Coated Solid Conductor

SAE-AS83519/1

  • SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I)

SAE-AS83519/2

  • SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PRE INSTALLED LEADS FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I)

SAE-AS85485/6

  • Cable, Electric, Filter Line, Component Wire, Silver-Coated High Strength Copper Alloy Conductor, Radio Frequency Absorptive, 150 Degrees C, 600-Volt

SAE-AS85485/10

  • Cable, Electric, Filter Line, Component Wire, Silver-Coated High-Strength Copper Alloy Conductor, Radio Frequency Absorptive, 150 Degrees C, 600-Volt

SAE-MA3275

NUT - SELF-LOCKING, CLINCH, SERRATED SHANK, 650 DEG. C, SILVER PLATED, UNS S66286, MJ THREAD, METRIC